Table of Contents
TogglePool water chemistry has two jobs: kill what bathers bring in, and keep the water from damaging the pool or the people in it. That means holding a disinfectant residual continuously, keeping pH in range so the disinfectant works, and balancing alkalinity, hardness and stabiliser around both.
Every bather introduces contamination continuously: sweat, skin, cosmetics, urine, and organisms. A pool is not disinfected once and then clean. It is disinfected constantly, against a load that arrives constantly.
The second job is protecting the pool and the bather. Water that is out of balance either dissolves the surfaces it touches, etching plaster and corroding metal, or deposits scale on surfaces, heaters and pipework. It also causes the eye and skin irritation most people wrongly blame on chlorine.
Chlorine is the most common disinfectant, and operators learn to read three numbers rather than one.
Free chlorine is what remains available to disinfect. This is the number that matters. Combined chlorine is chlorine that has already reacted with nitrogen compounds from bathers, forming chloramines. Total chlorine is the sum of the two.
A pool can show an adequate total chlorine reading while having almost no disinfecting capacity left, because most of it is combined. This is also the source of the sharp smell people describe as too much chlorine. A strongly smelling pool usually has too little free chlorine and too much combined, and the remedy is more disinfection rather than less.
Bromine is used in some settings, particularly warmer water, and behaves differently. It remains active when combined, which is an advantage, but it is more expensive and is not stabilised against sunlight.
The most important single number after free chlorine, because it controls how well the chlorine works.
Chlorine’s effectiveness falls sharply as pH rises. A pool reading an adequate chlorine level at a high pH is disinfecting far more slowly than the number suggests, and this relationship explains a large share of outbreaks traced back to pools.
Low pH is a different problem rather than a safer one. It is corrosive to surfaces, fittings and equipment, and it irritates eyes and skin.
Alkalinity is the water’s resistance to pH change, and it is why a pool with correct alkalinity holds its pH while one without swings wildly.
Too low and small chemical additions move pH dramatically, a condition operators describe as pH bounce. Too high and pH becomes stubborn, drifting upward and resisting correction.
This is why alkalinity is adjusted before pH rather than after. Correcting pH first, in water whose alkalinity is wrong, means correcting it again the next day.
The dissolved calcium in the water. Water low in calcium is aggressive and will take calcium from wherever it can find it, which means plaster, grout and concrete.
Too much produces cloudy water and scale on surfaces, in pipework and inside heaters, where it reduces efficiency and eventually causes failure. Hardness is straightforward to raise and difficult to lower, since the practical remedy is diluting with fresh water.
Used outdoors to protect chlorine from ultraviolet light, which otherwise destroys an unprotected residual within hours on a sunny day.
The trade off is that above a certain concentration it slows disinfection substantially, and it is not removed by anything except dilution. Outdoor pools that top up with stabilised chlorine products accumulate it steadily, and a pool with a very high reading can look chemically correct on paper while disinfecting poorly.
Indoor pools generally do not need it, and adding it there provides no benefit while creating the same problem.
Adjusting out of order is the most common reason operators find themselves chasing a pool that will not settle.
Free chlorine and pH are tested multiple times a day at a public pool, more often when it is busy. Alkalinity and hardness are tested weekly. Cyanuric acid is tested monthly outdoors.
Sample properly. Draw from elbow depth, away from a return inlet, in a clean container. Read in good light. A test strip glanced at in a dim plant room is not a measurement, and photometric or titration testing is considerably more reliable for the numbers that matter.
Record every test with the time, the tester, the readings and any chemical added. This log is the first thing an inspector asks for, and its absence is treated as evidence the pool was not operated correctly.
For related guidance, see CPO Certification, Pool Chlorine and pH and Pool Turnover and Filtration.
Free chlorine and pH together. Pool water chemistry depends on both because chlorine’s effectiveness falls sharply as pH rises, so a good chlorine reading at high pH is misleading.
Because it has too little free chlorine, not too much. In pool water chemistry that smell comes from chloramines, and the remedy is more disinfection rather than less.
Alkalinity, then pH, then hardness, then disinfectant. Adjusting pool water chemistry out of order is the usual reason a pool will not settle.
Free chlorine and pH several times daily at a public pool, alkalinity and hardness weekly. Pool water chemistry records should log the time, tester, readings and any chemical added.
For more on pool water chemistry, see the CDC’s Healthy Swimming guidance.
Last updated September 14, 2026